2003 - 2009 Dodge Ram 3500 6.7L Diesel Rear Suspension Torques

2004 Dodge Ram 3500 Rear End Torque Specs

Click the area you are looking for!


Dodge Ram 3500 6.7L Cummins Repair Information

Dodge Ram 3500 6.7L Cummins Rear End Repair Information

Here you can find information regarding repairs to the Dodge Ram 3500 rear end system. These repairs include the rear control arms installation, the rear swaybar information and bolt torque specs, the rear diff fluid change procedures, and the rear end watts system installation. All of these repairs and procedures include in depth details on how to perform the replacement and or repair. They also contain all the detailed torque specs needed for each bolt involved in the repair.

Rear Leaf Spring Installation

Dodge Ram 3500 Rear Leaf Spring
The rear suspension of the Dodge Ram 3500 consists of leaf springs and shock absorbers. The leaf springs are held together using a series of mounts and shackles. To start off the springs get held to the rear axle through the use of giant u bolts. These U-bolts contain nuts on the bottom of them that must be torqued down to 120 ft-lbs. I always use some loctite on these nuts as if they come off your entire rear end will come loose. Besides the U-bolts the rear suspension has a series of mounts that connect the leaf springs themselves to the vehicles frame. The leaf spring mounting nut gets tightened down to 175 ft-lbs. The shackle nuts get tightened down to 120 ft-lbs and the hanger bolts tighten to 35 ft-lbs. The center spring holder pin can be torqued down to 30 ft-lbs. This ensures that the leaf springs all stay stacked together.

Dodge Ram 3500 Rear Axle U-Bolts Torque Specs : 120 ft-lbs

Dodge Ram 3500 Leaf Spring Mounting Nut Torque Spec : 175 ft-lbs

Dodge Ram 3500 Shackle Nuts Torque Spec : 120 ft-lbs

Dodge Ram 3500 Spring Hanger Bolt Torque Spec : 35 ft-lbs

Dodge Ram 3500 Leaf Spring Center Pin Torque Spec : 30 ft-lbs

 

Rear Differential Torque Specs

Dodge Ram 3500 Rear swaybar
On the Dodge Ram 3500 the rear end ring gear bolts get tightened down to 150 ft-lbs. The rear carrier bearing caps can be tightened down to 100 ft-lbs. The rear differential backing plate to the differential get tightened down to 35 ft-lbs. Be sure to use some silicon sealant around the cover to ensure that the rear end fluid does not leak out.

Dodge Ram 3500 Rear End Ring Gear Torque Specs : 180 ft-lbs

Dodge Ram 3500 Rear Carrier Bearing Caps Torque Specs : 100 ft-lbs

Dodge Ram 3500 Rear Diff Backing Plate Torque Specs : 35 ft-lbs

 

Rear Shocks Installation

Dodge Ram 3500 Rear shock
To replace the rear shocks on a Dodge Ram 3500 you will need to remove two sets of bolts/nuts located at the bottom and top of the shock. Both of these fasteners can be accessed from underneath the vehicle by jacking it up and removing the wheel. To uninstall the old shock simply just remove both of the fasteners and the part will come out. When installing the new part reverse the procedure and tighten up both bolts to 75 ft-lbs.

Dodge Ram 3500 Rear Shock Upper Bolt Torque Specs : 75 ft-lbs

Dodge Ram 3500 Rear Shock Lower Bolt Torque Specs : 75 ft-lbs

 


Rear Leaf Spring Torque Specs
Rear Axle U-Bolts Torque Spec 120 ft-lbs
Leaf Spring Mounting Nut Torque Spec 175 ft-lbs
Leaf Spring Shackle Nut Torque Spec 120 ft-lbs
Leaf Spring Hanger Bolts Torque Spec 35 ft-lbs
Leaf Spring Center Pin Torque Spec 30 ft-lbs
Rear Differential / Axle Torque Specs
Rear End Ring Gear with E-locker Torque Spec 180 ft-lbs
Rear Carrier Bearing Cap Torque Spec 100 ft-lbs
Rear Axle Backing Plate Torque Spec 35 ft-lbs
Rear Shock Torque Specs
Rear Shock Upper Bolt Torque Spec 75 ft-lbs
Rear Shock Lower Bolt Torque Spec 75 ft-lbs