1998 - 2004 Dodge Intrepid 3.2L Front Suspension Torques

2000 Dodge Intrepid Front End Torque Specs

Click the area you are looking for!

Dodge Intrepid 3.2L Repair Information

Dodge Intrepid 3.2L Engine Repair Information

Here you can find information regarding the assembly of the Dodge Intrepid front end. In this guide we will cover the essential repairs for the front end of this vehicle. Included within these repairs is the inner and outer tie rod removal and change, the front wheel hubs installation, ball joint removal and installation, the upper and lower control arms, and the front strut installation. Along with the repair procedures we also include the corresponding bolt torque specs for each fastener involved. These guides are intended to assist in each procedure to help diyers with the job.

Dodge Intrepid Tie Rod Change/Removal

Dodge Intrepid Tie rod
To install a new tie rod on a Dodge Intrepid you must first remove the old one from the vehicle. This can be done by raising the vehicle up by either the use of a floor jack or a vehicle hoist. Once the vehicle is in the air you can remove the corresponding tire for the side that you want to change the tie rod on. Once the tire is off you can now access the old tie rod and remove it for replacement. On this vehicle the tie rod is apart of an entire rod system which controls the steering of the vehicle. If any of the steering rods are loose be sure to replace them appropiately. The outer tie rod itself connects with another inner portion of the rod through the use of an inner tie rod. This inner tie rod screws into the power steering rack and can be torqued down to 50 ft-lbs. Be sure to inspect and measure your old tie rods so that the new ones can be installed correctly. Whenever steering components are changed I recommend having an alignment done after the job to ensure the vehicle is in good functional condition. When putting the tie rod onto the vehicle the tie rod end nuts get tightened down to 30 ft-lbs. Be sure to install new cotter pins to ensure that vehicle safety is maintained.

Dodge Intrepid Outer Tie Rod End Torque Spec : 30 ft-lbs

Dodge Intrepid Inner Tie Rod Torque Spec : 50 ft-lbs


Front Wheel Hub Installation

Dodge Intrepid wheel hub
The front wheel hub on the Dodge Intrepid tightens down to the steering knuckle through the use of 4 bolts. In order to remove the old part from the vehicle you will need to jack your car up and remove the wheel on the side you are working on. From here we can then begin to remove the braking system by taking off the caliper and brake rotor and removing the center axle nut which holds the cv axle to the steering knuckle. With those removed we can now gain access to the wheel hub bolts which will be on the back side of the steering knuckle and can be accessed by turning the steering wheel one way and then the other. As you move the wheel take the bolts out as the access becomes easier. Once the 4 bolts have been removed you can remove the old part using a hammer and pry bar and then clean the surface and put the new part onto the vehicle. With the new wheel hub installed we can begin to hand tighten down the 4 bolts and then torque them to specs. The 4 bolts which hold it onto the steering knuckle should be torqued down to 80 ft-lbs. Once all are tight you can then put the center axle nut onto the cv axle and torque it down to 120 ft-lbs. Once both have been torqued you can proceed to reinstall the braking system and then the wheel.

Dodge Intrepid Front Axle Nut Torque Spec : 120 ft-lbs

Dodge Intrepid Wheel Hub Bolts Torque Spec : 80 ft-lbs


Front Ball Joints Installation

Dodge Intrepid Front Ball Joints
The Dodge Intrepid only has one front ball joint per each side of the vehicle. The lower ball joing connects the lower control arm to the vehicles steering knuckle. The lower ball joint can be slid into the steering knuckle and the pinch bolt and nut can be torqued down to 40 ft-lbs. Be sure that the ball joint tab was inserted all of the way into the steering knuckle before installing and torqueing down the bolt.

Dodge Intrepid Lower Ball Joint to Knuckle Torque Spec : 40 ft-lbs


Front Control Arms Installation

Lower Control Arm
Dodge Intrepid Front Control arms

On the Dodge Intrepid there is a single control arm for each side of the vehicle being the lower control arm. The lower control arm has 3 total fasteners which hold it to the vehicle. There are 2 bolts that hold the control arm to the vehicle frame. There is also a ball joint which fastens the control arm to the steering knuckle. The lower control arm frame bolts can both be tightened down to 90 ft-lbs while the vehicle is at ride height. From here the lower ball joint nut can be torqued down to 40 ft-lbs. When tightening up the lower control arm fasteners be sure to set the wheel height to a level that it would be at during riding or when on the ground. This is best done with a bottle jack under the suspension.

Dodge Intrepid Lower Arm Ball Joint Torque Spec : 40 ft-lbs

Dodge Intrepid Lower Arm Frame Bolts Torque Spec : 90 ft-lbs


Front Strut Installation

Dodge Intrepid Front struts
To replace the front struts on the Dodge Intrepid you will need to lift the vehicle up into the air and start by removing the tire on the side you want to replace. With that removed we can now remove the bolts and nuts that hold the strut to the vehicle frame and lower control arm. Starting with the 2 lower bolts which hold the strut assembly to the steering knuckle. Simply remove the nuts from the bolts and then lightly tap the bolts out of the steering knucle assembly. Be sure not to damage the threads on the bolts as they will need to be reused when installing the new strut into the vehicle. With the 2 lower bolts removed we can then remove the single nut which holds the stabilizer bar to the front strut. With that remove we can move to under the hood and remove the 3 nuts which hold the upper portion of the strut to the vehicles frame. With the upper three nuts removed the old strut assembly should be able to be removed from the car. The new strut assembly can be placed into the location of the old one and the upper nuts can be hand tightened. Before torqueing down any fasteners be sure that everything is first hand tightened. The 2 lower bolts can then be installed and hand tightened up along with the stabilizer endlink nut. From here we can torque down the upper nuts to 27 ft-lbs and then the 2 lower strut bolts to 125 ft-lbs. The stabilizer endlink can be torqued down to 17 ft-lbs.

Dodge Intrepid Front Strut Upper Nuts Torque Spec : 27 ft-lbs

Dodge Intrepid Front Strut Lower Bolts Torque Spec : 125 ft-lbs


Front Swaybar Installation

Dodge Intrepid swaybar
The front swaybar on the Dodge Intrepid consists of a series of brackets that hold it to the frame of the vehicle and a couple of endlink nuts that fasten it the the outer side of the car. To remove the swaybar you will need to jack up the front of the vehicle and remove both the endlink nuts as well as the brackets. To install the new swaybar you will need to move it back into the place as the old one and torque the endlink nuts to 17 ft-lbs and then torque the bracket bolts to 40 ft-lbs as well.

Dodge Intrepid Front Swaybar Bracket Torque Spec : 40 ft-lbs

Dodge Intrepid Front Swaybar Endlinks Torque Spec : 17 ft-lbs


Front Steering Torque Specs
Outer Tie Rod Endlink Torque Spec 30 ft-lbs
Inner Tie Rod Torque Spec 50 ft-lbs
Front Wheel Hub / Knuckle
Brake Caliper Slide Pin Torque Spec 27 ft-lbs
Front Wheel Bearing Hub Bolts Torque Spec 80 ft-lbs
Front Wheel Axle Nut Torque Spec 120 ft-lbs
Control Arms Torque Specs
Front Lower Ball Joint Nut Torque Spec 40 ft-lbs
Front Lower Arm Frame Bolts Torque Spec 90 ft-lbs
Front Shock and Extra Knuckle Torques
Front Strut Upper Nuts Torque Spec 27 ft-lbs
Front Strut Lower Bolts Torque Spec 125 ft-lbs
Stabilizer Frame Bracket Bolt Torque Spec 40 ft-lbs
Stabilizer End Link Torque Spec 17 ft-lbs